Stain & Finishing Oil All-In-One: HEARTWOOD--NEW!!

Eco-friendly and easy to use, the Stain & Finishing Oil All In One offers exceptional durability in high traffic areas like table tops, kitchen cabinets and even flooring. This is your go-to solution if you want to show off the grain of bare wood, but change the colour. Just apply with a brush or rag and wipe off the excess! www.fusionmineralpaint.com

Stain & Finishing Oil is a wood conditioner, stain and top coat all in one that offers exceptional durability in high traffic areas like table tops, kitchen cabinets, and even flooring.

Can be used on bare wood or over previously painted surfaces.No additional top coat required - it is highly durable as is. If you're looking for added durability, applying a coat of Natural will increase sheen and durability without intensifying your colour. 

If you apply it over Fusion Mineral Paint™ for a glaze effect or to increase the sheen, we recommend removing excess right away, as the SFO will not soak in and may leave a sticky finish that takes a few days to dry.

Use the Natural colour over Fusion Mineral Paint™ colours to increase the sheen and offer superior durability, or brush on one of the pigmented colours and wipe off immediately for a beautiful, easy glaze effect.

Our special blend is highly concentrated in pigment, so a little goes a long way. The 237 mL container will cover the same area as 1 litre of comparable stains.

Please keep in mind that all oil based products typically yellow in time. Using this over top of a white paint, will cause a slight yellowing effect. We recommend our Tough Coat for going over lighter colours to avoid yellowing. 

Fusion™ Mineral Paint Stain & Finishing Oil over bare wood.

Using our Stain and Finishing Oil (SFO) over bare wood is a straightforward process:

Begin by generously applying the SFO either by pouring it onto the surface or brushing it on, ensuring even coverage on the properly prepped and sanded wood.

After allowing it to penetrate for anywhere up to 15 minutes, remove any excess with a clean rag. For added depth of colour or increased sheen, consider applying a second coat after the recommended re-coat time of 9 hours.

The natural pigments in the SFO enhance the wood's grain, offering a beautiful accentuation. This product is a blend of natural oils and resins designed to penetrate deeply into the wood fibers, creating a robust, and water-resistant finish.

Unlike traditional topcoats, SFO doesn't form a surface film; instead, it becomes an integral part of your wood, providing long-lasting protection and enhancing its natural beauty.

Stain & Finishing Oil over Fusion™ Mineral Paint 

Stain and Finishing Oil (SFO) can be used over larger surfaces and over Fusion™ Mineral Paint to increase protection and the sheen, the more coats you apply the more increase in sheen will occur.

Over larger painted surfaces the SFO needs to be applied in thin amounts and buffed on. Applying in long strokes from end to end can result in lines or streaks. Over table tops for example you should apply the SFO in circular motions and ensure the excess is removed. You are aiming for the thinnest, even application possible.

Application Tool    Brush, lint free rag, applicator pad
Location     nterior/Exterior
Re-coat Time     9 hrs
Top Coat    No additional top coat is required.- this is made strong enough for floors and table tops. However you may use wax or "Natural" colour Stain & Finishing Oil to increase the sheen but not deepen the colour. 
Clean Up    Odourless Solvent 
Coverage     40-75 sq.ft. 
Finish/Sheen    Matte to high sheen. Each additional layer and buffing increases the sheen. 
Recommended Uses     Reclaimed wood, bare wood, table tops, floors, most any surface, painted finish or Milk Painted pieces. 
Can Be Applied To     Use as a stain over raw or well-sanded wood; apply over painted surface for added sheen, glaze effect, or added protection; seal milk paint or other porous paint. Not recommended over light colours as it will yellow.
Can Be Painted Over    Once dried if over bare wood and only 1 coat applied, 10 days after for multiple coats applied . Test to ensure prior to tackling a full project.
How to Prep     Apply over any surface or top coat for desired effect except wax.
Cure Time     10 Days
Maintenance/ Cleaning     Light cleaners, as they will strip away the natural oil.